Rig # 15 Inventory
10,000 feet Rig
Drawworks:
National T-45 Single Drum Drawworks powered by 2 Compounded 425 HP Series 3406 CAT Diesel 850 HP total, Drum grooved for 1 1/8” line, Foster makeup & breakout catheads, air drillers controls.
(Rebuilt 2007, replaced all bearings, clutches, sprockets & chains)
Base for Draw Works:
PJ-300 Base 12 feet wide by 40 feet long by 21 inch tall. 3 feet wide walk ways on two sides.
Hydramatic Brake:
WPT W36-OM-201 Water Cooled Brake with Double Clutch Rated at 500,000 lbs.
Derrick:
2012 model PJ 136-350, 136 feet, 350,000 lb, P.J. Jackknife Triple Derrick, PJ 8 line Crown Sheaves, 4” 4000 psi standpipe, racking board, and ladder. Crown-a-matic (Derrick – New 2012) designed for top drive.
Substructure:
2008 model PJ 4-12-670 elevating “Boot Strap” 12 feet Substructure. Rate for 670,000 lbs (New May 2008)
Powered Pumps:
#1 Gardner Denver Replica PZ-9 / QZ-9 Triplex, 1000 HP, forged steel fluid end w/ quick-change caps, relief valve, pressure gauge, cooling pump, 5 x 6 charge pump, master skid, powered by 800 HP Detroit Diesel 12V12000 with air clutch. Normally stocked with 6 ½” & 7” liners. (New 2008)
#2 Gardner Denver Replica PZ-9 / QZ-9 Triplex, 1000 HP, forged steel fluid end w/ quick-change caps, relief valve, pressure gauge, cooling pump, 5 x 6 charge pump, master skid, powered by 800 HP Detroit Diesel 12V12000 with air clutch. Normally stocked with 6 ½” & 7” liners. (New 2008)
Mud Pit System:
Shaker Tank 12’ 2” width x 6 ’ height x 42’ length 440 bbl, 2 each 5 x 6 centrifugal pumps each with 60 HP electric motors, 3 compartments, 3 mud agitators, internal plumbing, slant bottom, top mounted walkways, covered porch and master skid.
Suction Tank 8’ 9” width x 6’ height x 39’ length 320 bbl, 2 each 5 x 6 centrifugal mud mixing and transfer pumps each with 60 HP electric motors, 3 compartments – one with 60 bbl pill capacity, 5 each mud agitators, internal plumbing, slant bottom, top mounted walkways, covered porch and master skid.
Mud Cleaning Equipment:
2 each National/Varco D235-LI Linear Motion Shale Shakers with oilfield base and loop isolators. Unit excepts 3 hook strip screen panels for 23.5 sq feet of screen area on single deck, 2 explosion proof 1800 RPM vibrator motors rated at 1.5 HP each and explosion proof motor starter.
Double life I-130 De-Sander with 3 each 10 inch urethane cones, vitriolic couplings and header gauge. The unit is rated from 1500 to 1600 GPM at 65 to 75 head feet.
Double Life V-516 De-Silter with 16 each 5 inch urethane cones, elbows, vitriolic couplings and header gauge on a oilfield type skid. The unit is rated at 1600 GPM at 70 feet of head
Dog House & Fuel Tank Skid:
Dog House: 8’ width x 47’1” length skid mounted, insulated doghouse with knowledge box, lockers, Electric heat, Pilot II Automatic Driller, Electric Heat. Pason monitoring touch screen and EASTCO/Star 2 pen recorder.
Fuel Tank:
3,500 gallon diesel fuel tank mounted on skid with dog house.
Water Tank:
500 bbl, 8’ 6” width x 47’ length x 10’ 4” height water tank with 9 feet electrical room on end on tank.
Generator Set:
Primary Light Plant: Prime 545 eKW 681 kVA 60 Hz 1800 rpm 480 volts. Power by a CAT C-18 EPA certified tier 2 diesel, digital control panel with adjustable Hertz control. Electric start and low pressure kill, skid mounted. Storage & parts container mounted on same skid. Set up to handle 110 volt and 220 volt hook ups for directional trailers. All wiring and lighting on rig is explosion proof.
Recording & Monitoring Equipment: Rig equipped with PASON Electronic Drilling Recorder (EDR) Includes: Doghouse touch screen computer, Rig Site Server, Rig Management PC workstation, IADC approved Pason electronic work station, contractor morning report, Access to Pason Data Hub with drilling date a minimum twice daily, and commercial grade satellite dish receiver/transmitter. Pason Pit Volume Totalizer (PVT) not installed, but available through Pason.
Handling Tools & Auxiliary Tools:
BJ Style Type C tongs with heads sizes from 3 ½” to 10 3/4”. (New 2008)
4 ½” Drill Pipe slips
5 ½” through 7” Drill Collar slips
Drill Collar Safety Clamp
Elevators: 4 ½” BN, 4 ½” casing, 5 ½” casing, 8 5/8” casing
Cat head & Boom line, both with 1” rope
Martin Decker Type “D” Weight Indicator, 450,000 lbs WAT 102-01 Model 50(D) with 129T Anchor (New 2008)
4” ID Rotary Hose (New 2008)
1 Center Tub with 10 foot casing extension,
7 Pipe Tubs
Sure Shot deviation tool with wire line unit
Rotating & Traveling Equipment:
Gardner Denver 17 ½” Rotary Table (New 2008)
National Oilwell Single 160 Rotary Torque Gauge
T-200 Swivel National Oilwell Swivel (New 2008)
5 ¼” Hex Kelly 40 feet overall length, 37.75 working length (New 2008)
Varco Hex drive Kelly drive bushings (New 2008)
TP Products Model 77 Kelly Spinner
150 ton, 8 line traveling blocks with hydra-hook (New 2008)
1 1/8” Drill Line
Rat Hole and Mouse Hole
2 3/8” X 96” Elevator Links
Drill Pipe & Drill Collars:
10,000 feet of 4 ½” 16.6 #/ft, Grade G105 Drill Pipe with 4 ½” XH HB BN tool joints
12 each 6 ½” 99 #/ft 4 ½” XH Thread, Slip Recessed Drill Collars (6 1/2” OD, 2 ¼” ID)
